Single Point Load Cell, 300g/1kg/3kg/ 10kg/60kg/100kg/200kg to 500kg

After purchasing one ATO load cell, you can buy a special digital panel meter to obtain readings directly, or buy a transmitter to output standard signal to PLC, DCS and other systems. Customized output signal is 0-5V, 0-10V, or 4-20mA.

Note: The load cell cannot be connected to both the transmitter and the controller at the same time — only one can be selected.

Single point load cells have capacity range from 300g, 600kg, 1kg, 2kg, 5kg, 10kg, 40kg, 100kg to 500kg. Load cell capacity can be customized according to customer requirements. ATO high-accuracy single load cells are a low-cost, ideal choice for force and weight measurement in industries. With their extensive capacity range, they are versatile and applicable to a diverse array of uses.

Specification

Model	ATO-S-LCB-DYX-306
Weight	0.1~0.6kg
Capacity Range *	300g~500kg
Matched Display Controller	ATO-DPM-LC5D (Click it to the controller page)
Matched Transmitter	ATO-LCTR-OA (Click it to the transmitter page)
Accuracy	0.03%F.S (linearity + hysteresis + repeatability)
Sensitivity	2.0±0.5mV/V (Low range variations may differ)
Creep	±0.03%F.S/30min
Zero Output	±2%F.S
Temperature Effect on Zero	±0.03%F.S/10℃
Temperature Effect on Output	±0.03%F.S/10℃
Operating Temperature	-20℃~+80℃
Input Impedance	350±20Ω
Output Impedance	350±5Ω
Insulation Resistance	≥5000MΩ/DC 100V
Safety Overload	150%F.S
Ultimate Overload	300%F.S
Bridge Voltage (excitation voltage)	DC 10V
Maximum Bridge voltage (excitation voltage)	DC 15V
Material	2A12-T4 aluminum alloy
Protection Class	IP67
Cable Length	2m
Wiring	EXC+: Red, EXC-: Black, SIG+: Green, SIG-: White

Feature

High Precision Weighing: Features waterproof sealing, a wide measurement range, and stable performance. Suitable for various industrial automation weighing systems.
High Precision and Stable Performance: Easy to install, ideal for platforms, belt scales, and hoppers in industries like chemicals, pharmaceuticals, and food.
2A12-T4 Alloy Material: Strong fatigue resistance, excellent transparency, high strength, corrosion and heat-resistant.
Small Size and High Precision: Precision better than 0.03%, compact design, and long-term stable performance.

Dimension (unit: mm)

Single Point Load Cell Mounting Diagram

Wiring Method

Application

Tips: Single point parallel beam load cell features
In order to keep up with the development speed of the electronic pricing scale, the single point load cell should not only has the characteristics of high sensitivity and high rigidity, but also meet the requirements of short positioning time, strong anti-interference ability, good stability, etc. In addition, load cell is applicable to change for different capacities of electronic pricing scales. The ATO parallel beam load cell has the advantages of reducing the swing of the scale pan, short positioning time, stable and fast reading, and low-capacity anti-overload. In the future, parallel beam load cells will be more widely used in small electronic scales such as commercial or household electronic human health scales and electronic kitchen scales.

In this video, ATO will show you how to wire a strain gauge load cell with a display controller.

Low Profile Micro Compression Button Load Cell 100kg
This video introduces the specs, design features and applications of a low profile miniature button load cell DYHW-110 that's intended for compression force measurement. The maximum load capacity it can bear is 100kg. It can achieve 0.5%F.S accuracy with 150%F.S safety overload and temperature compensation.

Shear Beam Load Cell | Single & Double-Ended, Weighbridge Load Cells

The shear beam load cell is a common load cell. Its working principle is based on the deformation of the elastomer when it is acted upon by an external force. This deformation will cause the resistance of the elastomer to change, thereby achieving the measurement of the external force. It is typically used to measure forces in the small to medium range and its working principle is based on the shear effect of elastically deforming materials. This type of force measuring element is usually made of metal or polymer materials. Because of its high elastic modulus and shear modulus, it can produce stable shear deformation when subjected to external forces.

How to Ensure the Accuracy of Your Weighing System?

This video describes five factors that affect the accuracy of a weighing system and provides recommendations for selecting, installing, and operating the system to handle these factors.

Load Cell Transmitter 4~20mA Output Calibration

This video demonstrates how to calibrate the 4~20mA output. The 0~10V is also calibrated in the same way.

How Does PLC Read Data of Load Cell Transmitter?

In this video, it shows how PLC reads data from sensor transmitter. This system mainly consists of PLC, ATO load cell transmitter, ATO load cell, 24VDC power supply, personal computer, etc.

How to Make Your Load Cell Transmitter Work More Accurately

In this video, we've shown you how to calibrate the weight transmitter Model 610 by ATO using a compression load cell so that you can make sure you get the most accurate readings possible in your measurement.

CHB Load Cell Controller Calibration | Compensation Factor Calculation

In this video, we will walk you through the calibration procedure of ATO's CHB series load cell controller and how to calculate the compensation factor for your specific load cell so as to improve measurement accuracy. Hope you'll find it helpful.

How to Test for Faults in Load Cells?

As the most essential as well as vulnerable part of an electronic weighing system, load cells might get damaged for many different reasons. How can you determine whether a load cell is at fault? This video is gonna smooth out this problem by showing you several basic field tests that can be performed on site and provides the information necessary to interpret the results.

Load Cell Transmitter with Output 0-5V/0-10V/4-20mA/0-20mA

This intro video describes the features of ATO-DY510 load cell transmitter as well as its specifications. Housed in aluminum alloy case and CE-certified, the transmitter can connect to single or up tp 4 load cells at built-in excitation voltage from 5V to 15V DC. Powered from 18-30V DC supplies, this high precision weight transmitter can accept a 0-20mV full scale input range and convert the low strength signal into a 0-5V/0-10V/4-20mA/0-20mA output.

Cabled Tension Load Cell for Crane & Hoist Weighing Systems

In this introduction video, we've covered what the TJL-7 is, its specifications and some of the benefits that make it unique. This crane weigher is a strain gauge based alloy steel tension load cell designed with openings at either end. It has a high accuracy (0.03-0.05 F.S.) over a large and wide measurement range from 2t to 200t. Environmentally sealed to IP67, the crane load cell can withstand up to 150% safe overload.

Universal Miniature Compression & Tension Load Cell

In this video, we've presented two types of general-purpose micro load cells from ATO that can measure both compression and tensile forces. The capacitiy ranges are 1kg to 500kg (DYMH-103), 3kg to 500kg (DYMH-106). Both are made of nickle-plated stainless steel, featuring corrosion-resistant and rugged construction. Incorporating metal foil strain gauging, these precision load cells will deliver excellent stability, reliability and accuracy under various industrial circumstances.

Existing reviews of Single Point Load Cell, 300g/1kg/3kg/ 10kg/60kg/100kg/200kg to 500kg

Load Cell

Hi, We're looking at implementing a set of cantilever beam load cells and are looking for your technical feedback on our application. Here's a description of our application:

We're mounting a concrete mixer with a weight going from 150 to 156 kg between being empty and being full. That mass will be moving laterally on a set of motorized slides during process. We're planning on reading the weight only after we've stopped the axis from moving. We're expecting there will be non-constant moment/eccentric loads onto each load cells while the mass is being moved around. Would those loads skew the calibration of the load cell even if we're only taking a reading while the mass is stationary?

Looking forward to your feedback.

From: Grayson | Date: 26/11/2023